CircuitZone.com  Electronic Projects
Posted on Tuesday, January 28, 2014 • Category: AC / DC Innveters
Here is a simple but powerful, stable and efficient schematic diagram for a 500W modified sine wave inverter circuit. Originally I used a 555 timer and a CD4017 decade counter to produce the modified sine wave, but then I thought a simple PIC micro controller with its internal clock would produce a stable 50Hz/60Hz frequency without the need for two ICs. As you can see its a very simple circuit. 220V transformer should be used for 220V voltage output. For 110V voltage output use transformer with 110V rating.
Posted on Friday, December 23, 2011 • Category: AC / DC Innveters
This is a 500W DCtoAC inverter circuit diagram which produces an AC output at line frequency and voltage. 12VDC to 220V 50Hz inverter circuit will power 220V or 110V appliances from 12V car battery. The circuit is easy to make and is low cost. Use proper transformer. The output (in watts) is up to you by selecting different power rating transformer and power transistor rating. If you load electronic device which require 120V AC, then use transformer with 120V in output.
Posted on Monday, April 11, 2011 • Category: AC / DC Innveters
Small 1.5V to 5V or 12V DC/DC converter with LT1073 chip. The IC is available in three different versions, depending on output voltage. Two with fixed output voltage of 5V and 12V, and the most interesting that can be adjusted. The adjustment is done through a voltage divider with two resistors, of mass, output and Terminal 8, internally connected to the voltage comparator IC, which is responsible for stabilizing the output voltage.
Posted on Wednesday, April 6, 2011 • Category: AC / DC Innveters
24V to 12V 20A 400W DC to DC Inverter. Does little to change my PV system 12v 24v me the problem arose of what to do with investors who already had 12V. I was looking for a pattern online and found several schemes with linear regulators 20A, this solution although quite simple, due to the huge losses they have is not advisable. Ideally, a converter switched, highperformance. At the end I found nothing I liked and decided to design my own. Circuit characteristics: Output current: 20A at 12V (15A continuous and 30A Momentary), Input voltage: 18 to 30V DC, Output voltage: 5 to 20V, Operating Frequency: 70kHz, Effectiveness: 95%, 400W maximum power, Protections: Above current (30A) in the F1 circuit, D1 and F1 polarity in the circuit.
Posted on Wednesday, December 15, 2010 • Category: AC / DC Innveters
This circuit for Car audio input battery 12V to 50VDC, It use transistor and IC TL072.
Posted on Wednesday, November 17, 2010 • Category: AC / DC Innveters
The limitation of car supply voltage (12V) forces to convert the voltages to higher in order to power audio amplifiers.
In fact the max audio power x speaker (with 4 ohm impedance) using 12V is (Vsupply+  Vsupply)^2/(8*impedance) 12^2/32 = 4.5Watts per channel, that is laughable...
For powering correctly an amplifier the best is to use a symmetric supply with a high voltage differential. for example +20  20 = 40Volts in fact 40^2/32 = 50 Watts per channel that is respectable.
This supply is intended for two channels with 50W max each (of course it depends on the amplifier used). Though it can be easily scaled up or the voltages changed to obtain different values.
Posted on Wednesday, November 17, 2010 • Category: AC / DC Innveters
This is circuit Inverter 12VDC to 220V 50Hz 500W. It easy to make and low cost.
Posted on Wednesday, November 17, 2010 • Category: AC / DC Innveters
12V to 220V 100W transistor based power inverter.
Posted on Wednesday, November 17, 2010 • Category: AC / DC Innveters
I have done a lot of work with valves in recent years. For me valves have many advantages, least of all the price; since they are now "obsolete" it is quite easy to get hold of them for next to nothing at rally's and junk sales. I recently purchased a couple of hundred battery valves for less than SEK1 (US$ 0.15) each. The biggest problem with valves is the PSU needed to provide +250 vDC and 6.3 vAC for the filaments. The transformers are nolonger available at a reasonable price, but a pair of 12v6v0v6v12v mains transformers will do the job just as well. For portable use only one transformer is required together with a pair of power transistors such as 2N3055 etc.
Posted on Monday, October 18, 2010 • Category: AC / DC Innveters
This DC to AC inverter circuit work based on unstable multi vibrator does. In this circuit, IC CD4047 is chosen as a heart of unstable multivibrator, because this IC type gives a complementary output that has opposite phase to another ( pin 10 and 11 as seen in Figure 1), and has 50 % duty cycle that satisfy to generate a pulse for inverter.
Posted on Saturday, October 9, 2010 • Category: AC / DC Innveters
This is a DC to DC converter for car power amplifier. 12V input generates +30V and 30V output for preamp or power amplifiers. Circuit uses SG3525 IC, Mosfets and switching power supply.
Posted on Thursday, October 7, 2010 • Category: AC / DC Innveters
This circuit will provide a very stable "Square Wave" Output Voltage. Frequency of operation is determined by a pot and is normally set to 60 Hz. Various "off the shelf" transformers can be used. Or Custom wind your own FOR BEST RESULTS. Additional MosFets can be paralleled for higher power. It is recommended to Have a "Fuse" in the Power Line and to always have a "Load connected", while power is being applied. The Fuse should be rated at 32 volts and should be approximately 10 Amps per 100 watts of output. The Power leads must be heavy enough wire to handle this High Current Draw!
Posted on Wednesday, April 9, 2008 • Category: AC / DC Innveters
This is 100W inverter circuit. It uses 4047 IC and IRF540 Mosfet instead of 2N3055 transistor. Power output is 100W from 23A transformer.
CircuitZone.com © 2021. All Rights Reserved.
